|
Slate Tile |
Post Reply 
|
| Author | |
AndyMan 
Groupie 
Joined: 18/March/2009 Status: Offline Points: 54 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Slate TilePosted: 06/March/2010 at 8:18am |
|
Hello,
I am looking for some help with Slate tile. I am bidding on a 5k square foot facility of previously sealed slate tile. I do not know what has been used on the tile previously to seal it. The Facility is 50 years old so it probably has many different things on it. I tried to clean a sample area with traditional floor stripper and it cleaned it well but did not touch the sealer. I am considering just doing a deep scrub without stripper with a stiff brush and re-applying floor finish. I know I can get the floor clean enough for finish but I don't know if it will bond correclty and not flake off. Does anyone have any experience with this????
 |
|
|
AndyMan
|
|
 |
|
| Sponsored Links | |
|
|
|
Carpet Cleaning
Groupie
Joined: 16/July/2009 Status: Offline Points: 39 |
Post Options
Thanks(0)
Quote Reply
Posted: 10/March/2010 at 2:09am |
|
while you clean a slate floor, you want to remove dirt and stains with no damaging the tile or staining it. set up by establishing a few house policy, like not wearing shoes on your slate floor, which will help to decrease tracking. If you have slate flooring in the kitchen, use small throw rugs around the stove and the sink to catch spills before they hit the floor; likewise with a slate floor in the bathroom. These steps will make it much easier to clean a slate floor
|
|
|
|
|
Mark McMaster
Senior Member 
Joined: 22/October/2007 Location: Trenton,Ontario Status: Offline Points: 170 |
Post Options
Thanks(0)
Quote Reply
Posted: 17/March/2010 at 10:25pm |
|
I hope you price this accordingly. 5K, you'll be there a week if you don't know what's on that slate. 50 yrs old, that could be urethane on there as well.
Use some stripper to test and use some acetone as well. |
|
|
|
|
AndyMan
Groupie
Joined: 18/March/2009 Status: Offline Points: 54 |
Post Options
Thanks(0)
Quote Reply
Posted: 18/March/2010 at 7:45am |
|
actually I think it is urethane under there and I my plan was to not even attempt to remove it but instead just do a "soft scrub" with some neutral cleaner and a nylo brush on the end of my 175 rpm machine. I was also thinking of using the spinner to rinse well with the tm.. My only concern is if the floor finish will stick well considering I am not really stripping the old stuff off.. Do you have any experience with this???
|
|
|
AndyMan
|
|
|
|
|
Mark McMaster
Senior Member
Joined: 22/October/2007 Location: Trenton,Ontario Status: Offline Points: 170 |
Post Options
Thanks(0)
Quote Reply
Posted: 18/March/2010 at 10:54am |
|
. If it's urethane, you have to get it all off for sure or nothing is gonna bond.If it is urethane, use a paint stripper and then neutralize. Charge accordingly. Sometimes the gel strippers work better but you have to let it sit longer tho.
Edited by Mark McMaster - 18/March/2010 at 11:00am |
|
|
|
|
John Hilbrands
Newbie 
Joined: 21/April/2010 Location: Temecula Ca Status: Offline Points: 6 |
Post Options
Thanks(0)
Quote Reply
Posted: 21/April/2010 at 1:04pm |
|
I did about 100 floor cleanings 1000-2000 sq ft each last year and I never refinish. I guess if you want to make perfect strip and refinish but I usually do like you test the best cleaner and then just use it. I use the 175 rpm rotory & pole grout brush and then use a steam wand on skids and then towel dry.
On one clay tile it needed refinish due to bad previous sealers and even gel wouldn't remove it. I discovered sanding worked and said We could blast it. The customer called some "specialists" who said replacement was necessary. He called me back and I called a soda blaster it came out great.
Edited by John Hilbrands - 21/April/2010 at 1:17pm |
|
|
Sometimes you just have to go for it.
My website: http://www.hilbrandscarpetcare.com |
|
|
|
|
AndyMan
Groupie
Joined: 18/March/2009 Status: Offline Points: 54 |
Post Options
Thanks(0)
Quote Reply
Posted: 21/April/2010 at 3:29pm |
|
The conclusion to the story: I did use a floor cleaner (not floor stripper) I mopped on , let it set for a bit and scrubbed with a 175 machine and a stiff brush. I then rinsed with my truckmount and spinner. The rinsing process really worked well. I then put on 3 coats of high solids floor finish and it looks like glass!! client very happy which is what matters most!! Truckmount was the key here!! gotta love the heat!!
|
|
|
AndyMan
|
|
|
|
|
Post Reply
|
|
| Tweet |
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
Welcome to KleenKuip.com's Professional Carpet Cleaners Discussion Forum!